Guide :Grilling : Advantage 463453306

The second burner does not ignite

The only way I can get the second burner to ignite is by putting a match to it.  it should ignite by using the flame from the first one but it does not.

Research, Knowledge and Information :


What to Do When Your Furnace Does Not Ignite


The hot surface ignition system uses an electronic heating element to ignite the gas burner. ... What to Do When Your Furnace Does Not Ignite. November 11, 2013.
Read More At : gartnerhvac.com...

How to Repair an Electronic Ignition Gas Furnace


Because they can also come into play in repairing an electronic ignition furnace when it won ... name because by using a second heat ... burner will not ignite.
Read More At : www.thespruce.com...

Gas Range Burner Repair Tips | The Family Handyman


Gas Range Burner Repair Tips. Try these solutions before calling for service help. ... Clean the igniter and burner holes Start by cleaning the spark igniter ...
Read More At : www.familyhandyman.com...

Appliance Talk: Stove Top Burner or Burners Not Lighting


It's usually when the second one goes is when you start looking for information on how ... You turn your burner to light, ... Stove Top Burner or Burners Not Lighting.
Read More At : www.blog.applianceoutletservice.com...

Kitchenaid gas range Oven won't light broiler burner fine


As for you second question, ... Comments for Kitchenaid gas range Oven won't light broiler burner fine. ... the burner does not ignite again, ...
Read More At : www.appliance-repair-it.com...

Gas Burners Will Not Light - GE Appliances


Gas Burners Will Not Light. If your top burners will not work, follow the troubleshooting directions below before calling service: ... If you do not, ...
Read More At : products.geappliances.com...

What Causes a Dryer Ignitor Not to Ignite? | Home ... - SF Gate


The ignitor then produces heat to ignite a gas flame inside the burner ... What Causes a Dryer Ignitor Not to Ignite? ... If the ignitor glows and does not ignite ...
Read More At : homeguides.sfgate.com...

How do you troubleshoot gas furnace burners that do not ...


To troubleshoot gas furnace burners that do not ignite, inspect the pilot light, ensure the gas valve is on and perform other common troubleshooting tasks. Review the ...
Read More At : www.reference.com...

Suggested Questions And Answer :


I have a Summit Grill, six burners, and use natural gas. All igniters are working, except that none of the burners will stay lit for more than a few seconds. It acts like there's not enough gas pressu


Check the gas tubes for insects including spider webs those pesky critters love those tubes and screw up the airways.
Read More At : Grilling...

The second burner does not ignite


I have this grill and can not use it because evidently we were shorted the "vent" tent and the drippings from the food go directly onto the burner and clog the burner. So, anyone have any suggestions???
Read More At : Advantage 463453306...

I have a Grand Turbo 5 burner grill that is supplied by natural gas. When I open any one of the 5 valves to start the grilling party that is sure to follow, I hear the familiar high-pitched tone of the gas filling the burner, I hit the ignitor and....we have ignition!! But, the burner only stays lit for approximately1-2 seconds then dies out due to no gas flow. If I immediately repeat the process......nothing. But, if I wait for about 10 minutes and try again I get the same 1-2 seconds of flame then....nothing. Party's over folks.....


Hi, things to check, the Gas Regulator, the Hose, the Fitting... any protection circuitry. This is often caused by a faulty regulator, that won't supply the Gas properly.
Read More At : 38-inch Grand Turbo built-in 287003 (NG) All-in-One Grill /......

Brinkman second burner not lighting


Sometimes by the igniter there's a small deflector that directs 1 jet over to the gas outlet holes on the second burner. You can always get a butane extendo lighter and do it manually (or a match on hemostats)
Read More At : Brinkmann...

Second burner will not ignite on Weber grill


Its probably an obstruction in the burner. Take both the burners off and clean them inside and out with a brass brush. You need to clean them both, since the second burner is dependent on the first working properly. Step by step procedures are in your manual. Go to http://weber.com/help/manuals.aspx to download it.
Read More At : 1851001 Gas Grill...

Propane grill wont ignite


Well, it sounds like your grill is experiencing vapor lock. Vapor lock is basically air caught in the gas line and there is a relatively easy method to fix this. I want you to try this method and tell me what you get, ok? First, open the tank's valve, then open the burner valve and light the grill. Immediately after you see a blue flame, turn off the tank's valve, count to five and then close the burner valve. Repeat this procedure three times, the problem should clear itself. If you are still experiencing problems, the regulator may be faulty and needs to be tested next, so go get a new regulator from your Lowe's and run the procedure again. If after all this, you are still experiencing the problem, let me know here. Good luck!
Read More At : Grilling...

Two things....I changed the tanks out last night and I can't get the burners to light. Full tank of gas as I checked it. Took the burner covers off and cleaned the burner pipes itself and still nothing? Secondly, the igniter won't work and I changed the battery out. Old battery looked a little corrosive. Suggerstions?


Replace the regulator to get your burners to work you can get that at Home Depot, call Weber to get the other part, if your grill is under warranty you may get it Free!
Read More At : Genesis E-310 Gas Grill...

First burner ignites quickly, second and third take up to 3 minutes IF they fire at all. burners are not clogged.


If the first burner's flame characteristic's look right, the remaining burners need to be removed and the venturi valves and burner orifices checked for obstructions and cleaned if necessary.That's generally the cause of delay ignition.Hope this helped and Happy Grilling!
Read More At : CharBroil Master Flame Gas Barbecue Grill...

Model 141.163211 Kenmore BBQ Grill. Burner tube ignites then after a few seconds flames ignite behind control panel - melted knobs. A year ago same problem. Removed all parts and cleaned, installed new requlator & hose - This fixed it. This time I removed and cleaned all parts again but did not replace requlator - No fix.


It sounds like sealant may need to be used on connections. Use appropriate one for gas fittings. Noting where the leak is occuring is important. Another possibility is the fuel is being somehow "jetted" from a hole or orifice in a burner tube to the area behind the control panel. These are hard to see what happens first when it does happen.
Read More At : 16322...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mainebirdfood.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0383 seconds